PAP3200HV

Battery Charger Powerfinn PAP3200HV

Applicazioni

Caricabatterie - Bamer

Caricabatterie

Ferroviario - Bamer

Ferroviario

Harsh environment - Bamer

Harsh environment

Trasporti - Bamer

Trasporti

La serie PAP/HV di Powerfinn è caratterizzata da alimentatori programmabili ad alta potenza, leggeri, avanzati e dotati della moderna tecnologia switching. Tutti i dispositivi possono essere impiegati sia come alimentatori che come battery charger a tensione costante. La tensione in uscita e la corrente in ingresso possono essere regolate dal valore minimo 0 al valore massimo attraverso un trimmer interno presente nel pannello frontale, attraverso un controllo analogico opzionale 0-5V o un serial bus.


Caratteristiche:
Input voltage: 70…264Vac 1–phase ( 70…230Vac, reduced power )
                    70…369Vdc Efficiency 89% at full load, >90% at 50% load ( 230Vac input ) Input current 16A ( max)
Frequency:    47–63Hz Power factor >0.98
Inrush current: soft start
Output ripple:  <1%rms from maximum output voltage (1MHz bandwidth)
                     In S and T versions the resolution is defined by an 8-bit A/D converter of a
                     microcontroller. Measured using nominal output voltage.
Mechanics:     Wall mounting, see dimensions p. 3
Connectors:
    - Input: Input power cord
    - Output:SPT5/2-H-7,5 Phoenix
Enclosure:    Aluminum case, IP20
Weight:        7.1 kg without cables
Output Grounding: Floating
Ambient temperature range:   0°C…+40°C at full load, abs. max. +55°C
Overtemperature protection:   Processor controlled on/off
Overcurrent protection:   Electrical current limit
Reverse polarity protection: With fuse
Standards:
   - Safety: Class 1
             EN 60950-1
             LIMITATIONS
             Conformity can be limited depending on the end application output control method or unit mechanical structure.
             Note: If the charger’s rated output voltage is higher than 60VDC the charger doesn’t fulfill 1.2.8.7 (Safety Extra Low Voltage). Standard parts (2.1 Protection against electric shock) must be taken into account in installation.
             EN60335-2-29:2004
             EN60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006
             EN50366:2003 +A1:2006
             LIMITATIONS
             Conformity can be limited depending on the end application output control method or unit mechanical structure.
             Note: If the charger’s rated output voltage is higher than 36V it doesn’t fulfill article 10.101 (“The no-load d.c. output voltage shall not exceed 42.4V”)

- EMC:   Limits EN55022 Class B, Application must be discussed in detail

 

La serie PAP/HV di Powerfinn è caratterizzata da alimentatori programmabili ad alta potenza, leggeri, avanzati e dotati della moderna tecnologia switching. Tutti i dispositivi possono essere impiegati sia come alimentatori che come battery charger a tensione costante. La tensione in uscita e la corrente in ingresso possono essere regolate dal valore minimo 0 al valore massimo attraverso un trimmer interno presente nel pannello frontale, attraverso un controllo analogico opzionale 0-5V o un serial bus.


Caratteristiche:
Input voltage: 70…264Vac 1–phase ( 70…230Vac, reduced power )
                    70…369Vdc Efficiency 89% at full load, >90% at 50% load ( 230Vac input ) Input current 16A ( max)
Frequency:    47–63Hz Power factor >0.98
Inrush current: soft start
Output ripple:  <1%rms from maximum output voltage (1MHz bandwidth)
                     In S and T versions the resolution is defined by an 8-bit A/D converter of a
                     microcontroller. Measured using nominal output voltage.
Mechanics:     Wall mounting, see dimensions p. 3
Connectors:
    - Input: Input power cord
    - Output:SPT5/2-H-7,5 Phoenix
Enclosure:    Aluminum case, IP20
Weight:        7.1 kg without cables
Output Grounding: Floating
Ambient temperature range:   0°C…+40°C at full load, abs. max. +55°C
Overtemperature protection:   Processor controlled on/off
Overcurrent protection:   Electrical current limit
Reverse polarity protection: With fuse
Standards:
   - Safety: Class 1
             EN 60950-1
             LIMITATIONS
             Conformity can be limited depending on the end application output control method or unit mechanical structure.
             Note: If the charger’s rated output voltage is higher than 60VDC the charger doesn’t fulfill 1.2.8.7 (Safety Extra Low Voltage). Standard parts (2.1 Protection against electric shock) must be taken into account in installation.
             EN60335-2-29:2004
             EN60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006
             EN50366:2003 +A1:2006
             LIMITATIONS
             Conformity can be limited depending on the end application output control method or unit mechanical structure.
             Note: If the charger’s rated output voltage is higher than 36V it doesn’t fulfill article 10.101 (“The no-load d.c. output voltage shall not exceed 42.4V”)

- EMC:   Limits EN55022 Class B, Application must be discussed in detail