PAP3200

Battery Charger Powerfinn PAP3200

Applicazioni

Ferroviario - Bamer

Ferroviario

Harsh environment - Bamer

Harsh environment

Industriale - Bamer

Industriale

Trasporti - Bamer

Trasporti

La serie PAP di Powerfinn è caratterizzata da alimentatori ad alta potenza, leggeri, avanzati e dotati della moderna tecnologia switching. Tutti i dispositivi possono essere impiegati sia come alimentatori che come battery charger a tensione costante. La tensione in uscita e la corrente in ingresso possono essere regolate dal valore minimo 0 al valore massimo attraverso un trimmer interno presente nel pannello frontale, attraverso un controllo analogico opzionale 0-5V o un serial bus.


Caratteristiche:

- Ampio range in uscita 0-320Vdc
- Controllo analogico esterno 0-5Vdc
- Allarme avaria di potenza in uscita
- Connessione master-slave


Caratteristiche tecniche:

- Input voltage:

  • 70…264Vac 1–phase ( 70…230Vac, reduced power )
  • 70…369Vdc

- Efficiency: 89% at full load, >90% at 50% load ( 230Vac input )
- Input current: 16A ( max)
- Frequency: 47–63Hz
- Power factor: >0.98
- Inrush current: soft start
- Output ripple:

  • <1%rms from maximum output voltage (1MHz bandwidth)
  • In S and T versions the resolution is defined by an 8-bit A/D converter of a microcontroller. Measured using nominal output voltage.

- Mechanics Wall mounting, see dimensions p. 3
- Connectors:

  • Input: Input power cord
  • Output:
  1. Models 12V, 24V, 36V, 48V, copper busbar terminals
  2. Models 72V, 110V, 160V, 220V, 280V, 10mm2 3m output cables

- Enclosure: Aluminum case, IP20
- Weight: 7.1 kg without cables
- Output Grounding: Floating
- Ambient temperature range: 0°C…+40°C at full load, abs. max. +55°C
- Overtemperature protection: Processor controlled on/off
- Overcurrent protection: Electrical current limit
- Reverse polarity protection: With fuse ( 12VDC version doesn’t have fuse )
- Standards:

  • Safety Class 1
  • EN 60950-1

LIMITATIONS
Conformity can be limited depending on the end application output control method or unit mechanical structure.
Note: If the charger’s rated output voltage is higher than 60VDC the charger doesn’t fulfill 1.2.8.7 (Safety Extra Low
Voltage). Standard parts (2.1 Protection against electric shock) must be taken into account in installation.
EN60335-2-29:2004
EN60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006
EN50366:2003 +A1:2006
LIMITATIONS
Conformity can be limited depending on the end application output control method or unit mechanical structure.
Note: If the charger’s rated output voltage is higher than 36V it doesn’t fulfill article 10.101 (“The no-load d.c. output voltage
shall not exceed 42.4V”).

  • EMC Limits EN55022 Class B, Application must be discussed in detail

La serie PAP di Powerfinn è caratterizzata da alimentatori ad alta potenza, leggeri, avanzati e dotati della moderna tecnologia switching. Tutti i dispositivi possono essere impiegati sia come alimentatori che come battery charger a tensione costante. La tensione in uscita e la corrente in ingresso possono essere regolate dal valore minimo 0 al valore massimo attraverso un trimmer interno presente nel pannello frontale, attraverso un controllo analogico opzionale 0-5V o un serial bus.


Caratteristiche:

- Ampio range in uscita 0-320Vdc
- Controllo analogico esterno 0-5Vdc
- Allarme avaria di potenza in uscita
- Connessione master-slave


Caratteristiche tecniche:

- Input voltage:

  • 70…264Vac 1–phase ( 70…230Vac, reduced power )
  • 70…369Vdc

- Efficiency: 89% at full load, >90% at 50% load ( 230Vac input )
- Input current: 16A ( max)
- Frequency: 47–63Hz
- Power factor: >0.98
- Inrush current: soft start
- Output ripple:

  • <1%rms from maximum output voltage (1MHz bandwidth)
  • In S and T versions the resolution is defined by an 8-bit A/D converter of a microcontroller. Measured using nominal output voltage.

- Mechanics Wall mounting, see dimensions p. 3
- Connectors:

  • Input: Input power cord
  • Output:
  1. Models 12V, 24V, 36V, 48V, copper busbar terminals
  2. Models 72V, 110V, 160V, 220V, 280V, 10mm2 3m output cables

- Enclosure: Aluminum case, IP20
- Weight: 7.1 kg without cables
- Output Grounding: Floating
- Ambient temperature range: 0°C…+40°C at full load, abs. max. +55°C
- Overtemperature protection: Processor controlled on/off
- Overcurrent protection: Electrical current limit
- Reverse polarity protection: With fuse ( 12VDC version doesn’t have fuse )
- Standards:

  • Safety Class 1
  • EN 60950-1

LIMITATIONS
Conformity can be limited depending on the end application output control method or unit mechanical structure.
Note: If the charger’s rated output voltage is higher than 60VDC the charger doesn’t fulfill 1.2.8.7 (Safety Extra Low
Voltage). Standard parts (2.1 Protection against electric shock) must be taken into account in installation.
EN60335-2-29:2004
EN60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006
EN50366:2003 +A1:2006
LIMITATIONS
Conformity can be limited depending on the end application output control method or unit mechanical structure.
Note: If the charger’s rated output voltage is higher than 36V it doesn’t fulfill article 10.101 (“The no-load d.c. output voltage
shall not exceed 42.4V”).

  • EMC Limits EN55022 Class B, Application must be discussed in detail